motoring|underground  
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read Blog

Braking Clamping the binders.

Go Back   motoring|underground > On the Lifts > Braking
Reply
 
Thread Tools
  #1  
Old 07-28-2009, 07:20 PM
coendek coendek is offline
Y Rated - 186 mph
 
Join Date: Jan 2008
Posts: 2,007
Default DIY changing brakes

Hiya Guys,

I just bought a set of APracing brakes, rotor's pads and the brakes itself.

Is there a HOW TO??? so I can switch them myself?!

Thanks in advance!

Coen
Reply With Quote
  #2  
Old 07-28-2009, 07:57 PM
Scotty's Avatar
Scotty Scotty is offline
Retired
 
Join Date: May 2007
Location: Darmstadt, Germany
Posts: 2,457
Send a message via ICQ to Scotty
Default

If you can read german, I could send you a couple of PDFs from the MINI maintenance database

But it's quite simple.

1. Take off wheel
2. Remove complete caliper setup by loosening the two 14(?)mm screws with a wrench and take off caliper.
3. Remove brake line and fix brake line to new caliper.
4. Remove old brake disk (Torx40 or Torx45). MINI says, you neet to replace that screw
5. Clean bearing with sandpaper or wire brush and mount new disk. Tighten the Torx screw to 27NM
6. Mount new caliper and mount new brake pads. Tighten screws holding the caliper to 110NM
7. Bleed brake fluid and refill reservoir.

Repeat for 2nd wheel.

Make sure:
- you have pushed the pistons right in
- you break the edges of the new brake pads with a bit of sandpaper
- use some grease or copper paste on the hooks were you fit the brake pads

Did I forget anything?

Ah yes:
- before you start, top off the brake fluid untill the reservoir is really full, so you don't get any air in your system.
- if you install a new brake you might want to completely bleed your brake fluid. You need roughly one litre for a complete flush.
- If you bleed completely, dont forget to bleed the clutch too
- bleed brake by brake and have someone watch the fluid level in the reservior and top off the brake fluid if needed.
__________________

9 of 10 voices inside my head say I'm crazy. One is whistling...

Last edited by Scotty; 07-28-2009 at 10:32 PM..
Reply With Quote
  #3  
Old 07-28-2009, 08:15 PM
coendek coendek is offline
Y Rated - 186 mph
 
Join Date: Jan 2008
Posts: 2,007
Default

scotty!! PLEASE!!!

coendekorte @ hotmail. com

Thanks!!

would be great!!!
Reply With Quote
  #4  
Old 07-28-2009, 08:16 PM
coendek coendek is offline
Y Rated - 186 mph
 
Join Date: Jan 2008
Posts: 2,007
Default

btw.. is it that BIZARRE easy?!
Reply With Quote
  #5  
Old 07-28-2009, 10:02 PM
CIGARGUY's Avatar
CIGARGUY CIGARGUY is offline
μ
 
Join Date: Nov 2006
Location: Safety Harbor, FL
Posts: 4,522
Default

Yes. It is that easy.
__________________
Click the image to open in full size.

Two wrongs don't make a right, but three rights make a left.
Reply With Quote
  #6  
Old 08-26-2009, 01:47 PM
Jeffsmashkot Jeffsmashkot is offline
Y Rated - 186 mph
 
Join Date: Jun 2009
Location: Woodbridge, NJ
Posts: 103
Default

Is that TORX40/TORX45 screw widely found from a Pepboys/Autozone/Strauss/NAPA?

---

Edit: Never mind, appears that it's only for aligning purposes. The caliper should hold it together, and if you have studs, then they'll align it for you.

Last edited by Jeffsmashkot; 08-26-2009 at 02:35 PM..
Reply With Quote
  #7  
Old 08-27-2009, 02:12 PM
onasled's Avatar
onasled onasled is offline
Y Rated - 186 mph
 
Join Date: Jan 2007
Location: Hampton, Ct
Posts: 338
Default

The only part that may NOT be easy is bleeding the clutch slave. Honestly, I would just stay away from this part.
Couple of things. Dont add any fluid to the reservoir untill after you compress your caliper pistons, or you will end up overflowing the res. Add the fluid after you get everything installed and then start the bleeding.
You need a good size C clamp, or special tool to compress the rear calipers due to the internal E brake. The need to be turned clockwise while being pushed in. I have always done this with a C clamp and have never needed that tool.
Make sure you keep your new rotors and pads CLEAN during instalation. Not sure I would use any grease near the pads.
It's a dirty job. Haaa. And no, you don't need to get new torx head bolts that hold the rotors on. They do little.
__________________
http://www.motoringunderground.com/forum/image.php?type=sigpic&userid=1037&dateline=1232243  339
Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


CURRENT MOON

All times are GMT. The time now is 12:30 PM.
Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
2005 motoring|underground, all rights reserved.